Code: EQD-AFT3RRP: $399.99

Earthquaker Devices Afterneath V3 Reverb Pedal

Pre-order available

$349.00 incl GST

Pre-order available

Payment Options: Master card, Visa, American Express and PayPal logo

The Earthquaker Devices Afterneath V3 sounds a lot like it looks – a wizard bursting forth from ethereal cave and ready for the ambient battle. You are the wizard – or sorceress, if you prefer – and the cave is your instrument’s signal, vast, expansive, and magical. Do you go inside? Roll a D20 to proceed!

Once inside, a reflection of light from an unknown source catches your eye, and you notice a bizarre sheen on the walls of the cave. You timidly inch closer to the walls of the cave. Placing your hand gently on the cavern wall, you feel the rock move. The cave is alive! Alarmed, you emit a loud gasp, which reverberates throughout the subterranean landscape. Upon further listening, it appears as though the reverberations of your voice are in fact a swarm of short digital delays which may be used to create wild and cavernous reverbs, or scattered, short, rhythmic delays with bizarre characteristics. The Earthquaker Devices Afterneath V3.

Dimensions: 4.75 x 2.50 x 2.25 in. (121 x 64 x 57 mm) with knobs


Current Draw: 100 mA


Input Impedance: 1 MΩ


Output Impedance: 500 Ω


Expression Jack

This is an expression pedal control jack for the Drag. The Afterneath requires an expression pedal with a value of 50k, we recommend the Moog EP-3 or similar.  While it will work with a standard 10k expression pedal, a 50k expression pedal will allow you to access the full range of each mode.

  • Tip is the wiper, Ring is 5v and Sleeve is ground.

  • You can also use CV with this jack. CV operates 0-5v.


Flexi-Switch® Technology

This device features Flexi-Switch Technology! This electronic switching style allows you to simultaneously use momentary and latching style switching.

  • For standard latching operation, tap the footswitch once to activate the effect and then tap again to bypass.

  • For momentary operation, hold the footswitch down for as long as you’d like to use the effect. Once you release the switch, the effect will be bypassed.

The Afterneath uses electronic buffered bypass, it requires power to pass signal and the buffer is always active. You may experience a pop the first time the Afterneath is switched on after power up.


Tails / No Tails Switching

The Afterneath is factory set in “tails mode.” This means that the wet signal will naturally decay and slowly fade to silence after the effect is switched off.

To deactivate this feature:

  • Unplug the power cable from the power jack.

  • Hold down the footswitch and insert the power cable.

  • The LED will flash 3 times. You can now release the footswitch.

Follow the same steps to reactive tails mode.


Power

This device takes a standard 9 volt DC power supply with a 2.1mm negative center barrel. We always recommend pedal-specific, transformer-isolated wall-wart power supplies or multiple isolated-output supplies. Pedals will make extra noise if there is ripple or unclean power. Switching-type power supplies, daisy chains and non-pedal specific power supplies do not filter dirty power as well and let through unwanted noise. DO NOT RUN AT HIGHER VOLTAGES!

This product is covered by a limited lifetime manufacturer warranty.

Although we are not authorised to determine if any repair is covered under warranty, if the item was purchased through World of Music, then we are often the best people to facilitate the claim for you and will do so as timely as possible. Warranty does not apply to cosmetic damage or faults that are a result of user neglect. Although your mate is really handy with a soldering iron, any product modification or home repair will also result in a void warranty.

Quite often, something perceived as a fault is as simple as a faulty cable or power issue so we always suggest checking over Frequently Asked Questions on the manufacturer website first. It can be a helpful approach to getting to the bottom of a problem and save you a lot of time in getting your gear back up and running!

This item ships via Australia Post; fully insured for your piece of mind. Orders require a signature on delivery and we suggest using an address where someone will be present for the speediest delivery time. For delivery attempts where no one is present, your order will be taken to your allocated Australia Post location for pickup. A card will be left with instructions of where and when you can collect your order.

Product Description

The Earthquaker Devices Afterneath V3 sounds a lot like it looks – a wizard bursting forth from ethereal cave and ready for the ambient battle. You are the wizard – or sorceress, if you prefer – and the cave is your instrument’s signal, vast, expansive, and magical. Do you go inside? Roll a D20 to proceed!

Once inside, a reflection of light from an unknown source catches your eye, and you notice a bizarre sheen on the walls of the cave. You timidly inch closer to the walls of the cave. Placing your hand gently on the cavern wall, you feel the rock move. The cave is alive! Alarmed, you emit a loud gasp, which reverberates throughout the subterranean landscape. Upon further listening, it appears as though the reverberations of your voice are in fact a swarm of short digital delays which may be used to create wild and cavernous reverbs, or scattered, short, rhythmic delays with bizarre characteristics. The Earthquaker Devices Afterneath V3.

Specifications

Dimensions: 4.75 x 2.50 x 2.25 in. (121 x 64 x 57 mm) with knobs


Current Draw: 100 mA


Input Impedance: 1 MΩ


Output Impedance: 500 Ω


Expression Jack

This is an expression pedal control jack for the Drag. The Afterneath requires an expression pedal with a value of 50k, we recommend the Moog EP-3 or similar.  While it will work with a standard 10k expression pedal, a 50k expression pedal will allow you to access the full range of each mode.

  • Tip is the wiper, Ring is 5v and Sleeve is ground.

  • You can also use CV with this jack. CV operates 0-5v.


Flexi-Switch® Technology

This device features Flexi-Switch Technology! This electronic switching style allows you to simultaneously use momentary and latching style switching.

  • For standard latching operation, tap the footswitch once to activate the effect and then tap again to bypass.

  • For momentary operation, hold the footswitch down for as long as you’d like to use the effect. Once you release the switch, the effect will be bypassed.

The Afterneath uses electronic buffered bypass, it requires power to pass signal and the buffer is always active. You may experience a pop the first time the Afterneath is switched on after power up.


Tails / No Tails Switching

The Afterneath is factory set in “tails mode.” This means that the wet signal will naturally decay and slowly fade to silence after the effect is switched off.

To deactivate this feature:

  • Unplug the power cable from the power jack.

  • Hold down the footswitch and insert the power cable.

  • The LED will flash 3 times. You can now release the footswitch.

Follow the same steps to reactive tails mode.


Power

This device takes a standard 9 volt DC power supply with a 2.1mm negative center barrel. We always recommend pedal-specific, transformer-isolated wall-wart power supplies or multiple isolated-output supplies. Pedals will make extra noise if there is ripple or unclean power. Switching-type power supplies, daisy chains and non-pedal specific power supplies do not filter dirty power as well and let through unwanted noise. DO NOT RUN AT HIGHER VOLTAGES!

Warranty

This product is covered by a limited lifetime manufacturer warranty.

Although we are not authorised to determine if any repair is covered under warranty, if the item was purchased through World of Music, then we are often the best people to facilitate the claim for you and will do so as timely as possible. Warranty does not apply to cosmetic damage or faults that are a result of user neglect. Although your mate is really handy with a soldering iron, any product modification or home repair will also result in a void warranty.

Quite often, something perceived as a fault is as simple as a faulty cable or power issue so we always suggest checking over Frequently Asked Questions on the manufacturer website first. It can be a helpful approach to getting to the bottom of a problem and save you a lot of time in getting your gear back up and running!

Shipping

This item ships via Australia Post; fully insured for your piece of mind. Orders require a signature on delivery and we suggest using an address where someone will be present for the speediest delivery time. For delivery attempts where no one is present, your order will be taken to your allocated Australia Post location for pickup. A card will be left with instructions of where and when you can collect your order.