Walrus Audio Melee Wall of Noise

MELEE: WALL OF NOISE
We give you the two most quintessential effects that yield unruly amounts of power and influence to an instrumentalist: reverb and distortion. They have been harnessed and woven together for an eternity of ethereal power with The Melee: Wall of Noise. The Melee unapologetically uses a joystick to meld reverb and distortion into one massive blaze of sound. With the flip of the order switch, run the distortion into the reverb or reverb into distortion; signal chain is your call now. For the explorer, the Melee can run one of three different reverb programs Ambient, Octave, and Reverse.

In a less is more approach, we’ve intentionally decided on controls that are fun to use and will inspire a wealth of creative output. Use the joystick to control the amount of distortion by moving it up and down. Moving the joystick left and right will adjust your reverb mix. The tone and decay toggles have low, medium, and high settings. Modulation can be added to the wet signal by holding down the bypass switch and moving the decay toggle. The left position is no modulation, the middle is a slight modulation, and the right is a high modulation.

ALGORITHMS
The Melee is equipped with three different reverb programs, which can be changed by simultaneously pressing the bypass and sustain stomp switches. Experiment with the order toggle switch to hear how differently these all react in front and after the distortion!

• Ambient Reverb (Pink LED) - Huge reverb capable of massive trails and engulfing your chords into an angry wash of sound. Great for soaring melodic lines or shoegaze-driven chord progressions.
• Octave Down Reverb (Yellow LED) - Similar to the Dark mode in the Slö, you’ll find an eerie lower octave hovering in the reverb trail for a nice and dark atmospheric touch.
• Reverse Reverb with Feedback (Blue LED) - Add reversed reverb trails back into your signal, create gentle melodies or push into reverse feedback overload. Big, slow, and sad chords love to hang out here.

MOMENTARY
Press and hold the sustain switch to ramp up the reverb trails. Release and the trails will ramp back down to where the decay switch is currently set. The sustain switch can also latch in all three programs. Press and release the Sustain switch to capture and sustain the current reverb decay for long pad-like sounds in your wet mix. Press again to release the latch, and the reverb trail will taper off based on the position of the decay knob.

• The Melee comes coated in a glossy neon pink enclosure with white, yellow, and green inks with art by David Hüttner.
• The die-cast enclosure’s exact size is 3.62” x 4.79” x 3.14” (including joystick height).
• Three bypass modes, DSP, DSP+True, True Bypass
• Power requirements are 9VDC, centre negative (200mA minimum).
• The use of an isolated power supply is recommended for powering all Walrus Audio Pedals.
• Daisy chain power supplies are not recommended.
• Power supply not included.

Walrus audio products are covered by a limited lifetime manufacturer warranty.

Although we are not authorised to determine if any repair is covered under warranty, if the item was purchased through World of Music, then we are often the best people to facilitate the claim for you and will do so as timely as possible. Warranty does not apply to cosmetic damage or faults that are a result of user neglect. Although your mate is really handy with a soldering iron, any product modification or home repair will also result in a void warranty.

Quite often, something perceived as a fault is as simple as a faulty cable or power issue so we always suggest checking over Frequently Asked Questions on the manufacturer website first. It can be a helpful approach to getting to the bottom of a problem and save you a lot of time in getting your gear back up and running!

This item ships via courier; fully insured for your peace of mind. Orders require a signature on delivery and we suggest using an address where someone will be present for the speediest delivery time. For delivery attempts with no one present to sign, your order will be taken to the courier depot and a card will be left for you to organise redelivery.